SYSTEM_STATUS: ACTIVE

Ultimate Gamepad Health Hub

A screening check for your controller. We test each part on its own, sticks, buttons, triggers, vibration, and connection, and show a pass or a fail for each part.

1TEST
2DATA
3AUDIT

Phase 1: Real-Time Performance Inputs

Get from Drift Tester Flickers within 0.02 to 0.03 are normal noise. A steady 0.05 to 0.10 is mild drift. A steady offset above 0.10 is clear drift.
Get from Lag Tool Browser estimate: under 8 ms

Results by Part

Each part passes or fails on its own. There is no single score. Test a failing part separately with its dedicated tool.

Hardware Comparative Analysis

PartPassFail
Sticks at restRest value steady at 0.10 or below after a clean retest, with no creepSteady above 0.10, creeping in one direction, or random jumps while untouched
Buttons and D-padEvery button registers once per press, no ghost press, no sticking buttonAny button misses, double registers, ghosts, or sticks
TriggersFull range from 0.00 to 1.00, returns to restStops short of full pull, does not return to rest, or misfires
VibrationEach motor responds when testedA motor does not respond, or responds weakly on one side only
ConnectionController detected, steady report rate at the expected native rate for the controller and connectionNot detected, wild jumps, dropouts, or a rate far below the expected native rate

Health here means a pass or a fail per part. There is no single health score, no percentage, and no grade.

Diagnostic Knowledge Base

What is "Signal Jitter"?

It is the instability in your stick's raw data. Even without drift, high jitter means your aim will feel shaky. We show it as part of the stick result, not as a score.

Can firmware fix mechanical drift?

No. Firmware can only adjust deadzones. Physical wear on the stick parts requires a part repair or replacement. Firmware alone cannot fix true mechanical drift.

Why is Hall Effect the gold standard?

Hall effect sticks use magnetic sensing with no friction wear in the sensing path, so they resist drift longer than potentiometer sticks. They are not drift-proof. A weak centering spring or a calibration problem can still cause drift.

How often should I test health?

Competitive gamers should run a full audit every 3 months or after 500 hours of gameplay.

Does overclocking improve health?

No. Overclocking is a PC wired only option, and it can make readings unstable. It does not change the health result, because health here is a pass or a fail per part, not a score.

What is "Ghosting"?

When a button press is registered without you touching it. A button that registers without a press fails the button check. Test every button again with the button test.

What does a steady rest value above 0.10 mean?

A steady offset above 0.10 is clear drift. Clean and calibrate first, then decide between repair and replace. A deadzone setting only hides the offset, it does not fix the hardware.

Why is battery life not included?

Battery is a separate module. We focus on Input Performance which directly affects your K/D ratio.

Do Scuf controllers last longer?

Internal boards are similar to standard PS5 units, but their modular nature makes them easier to repair.

What causes trigger delay?

Usually, the internal rubber membrane is torn or the spring has lost tension. Test the trigger range with the trigger test. If the trigger does not reach full pull or does not return to rest, it fails the trigger check.

Universal Diagnostic Hub

Complete your controller audit using our specialized testing suite. Each tool is precision-engineered to target specific hardware components—from analog sensors to circuit response times.

What a Health Check Covers, and What It Does Not

A health check is a screening pass over your controller. It looks at the parts that a browser can actually read through the Gamepad API, so you can spot which part needs a closer look. It does not repair anything, it does not certify a controller, and it does not replace the dedicated tools below.

This check screensThis check does not diagnose
Stick drift at restLab-grade latency (browser estimates only)
Stick deadzoneNative haptics or impulse triggers
Buttons and D-pad inputsHD Rumble detail
Trigger rangeModule-level repair diagnosis
Vibration responseWhether a module needs replacement
Polling behaviorEnd-to-end system latency

The rule: a health check is screening, not a repair diagnosis. If one part fails, test it separately with its dedicated tool and record the before number so you can compare after any fix.

Test the Failing Part Separately

If the health check flags one area, take that part to its own tool for a precise reading:

What Your Result Means

  • Everything passes but the game feels slow: run the input lag test and check your polling rate next.
  • One part fails: take it to its dedicated tool from the list above and record the before number.
  • Multiple parts fail: that points to a repair vs replace decision. Our repair vs replace guide is coming later.
  • Controller not detected at all: fix detection first. See the controller not detected troubleshooting steps: press a button to wake the API, refresh, try another port or cable, use Chrome or Edge, and close remappers.

Limitations of This Check

All readings here are browser estimates through the Gamepad API, not lab measurements. A pass does not certify a controller for tournament play. A single fail does not prove the controller is unusable. Retest the failing part separately with its dedicated tool first.

How we test is documented in our testing methodology and on the about page.

Last updated: 14 November 2026